Bengaluru, Karnataka
GST No. 29AESPS6845P1Z3
Industrial Electronic Components
We are offering Industrial Electronic Components as per clients specification and needs that are at par with international standards.Integrated Circuits ICs
-
-
-
- +9
Approx. Rs 15 / PieceGet Latest Price
Product Details:| Minimum Order Quantity | 500 Piece |
| Number Of Pins | 40 Pins |
| Mounting Type | Through Hole |
| Type | Non-Leaded, Leaded |
| Brand | Toshiba, Analog Devices, Atmel |
| Functionality | Processor, Micro Controller |
| Power | ON |
| Phase | single |
| Color | Microchip |
Among the most advanced integrated circuits are the microprocessors or "cores", which control everything from computers and cellular phones to digital microwave ovens. Digital memory chips and ASICs are examples of other families of integrated circuits that are important to the modern information society. While the cost of designing and developing a complex integrated circuit is quite high, when spread across typically millions of production units the individual IC cost is minimized. The performance of ICs is high because the small size allows short traces which in turn allows low power logic (such as CMOS) to be used at fast switching speeds.
ICs have consistently migrated to smaller feature sizes over the years, allowing more circuitry to be packed on each chip. This increased capacity per unit area can be used to decrease cost and/or increase functionality—see Moore's law which, in its modern interpretation, states that the number of transistors in an integrated circuit doubles every two years. In general, as the feature size shrinks, almost everything improves—the cost per unit and the switching power consumption go down, and the speed goes up. However, ICs with nanometer-scale devices are not without their problems, principal among which is leakage current (see subthreshold leakage for a discussion of this), although these problems are not insurmountable and will likely be solved or at least ameliorated by the introduction of high-k dielectrics. Since these speed and power consumption gains are apparent to the end user, there is fierce competition among the manufacturers to use finer geometries. This process, and the expected progress over the next few years, is well described by the International Technology Roadmap for SemiconductorsElectronic Piezo Buzzer
-
-
-
- +10
Approx. Rs 7 / PieceGet Latest Price
Product BrochureProduct Details:| Minimum Order Quantity | 1000 Piece |
| Voltage | 12.0 V |
| Brand | Different Type of Brand |
| Frequency | 2.8 KHz |
| Color | Black |
| Buzzer Size | 42MM |
| Material | FR4 ABS |
| Volatge | 5v,12v |
A buzzer or beeper is an audio signaling device which may be mechanical, electromechanical, or piezoelectric. Typical uses of buzzers and beepers include alarm devices, timers and confirmation of user input such as a mouse click or keystroke.
The piezo buzzer produces sound based on reverse of the piezoelectric effect. The generation of pressure variation or strain by the application of electric potential across a piezoelectric material is the underlying principle.
Piezo buzzer is an electronic device commonly used to produce sound. Light weight, simple construction and low price make it usable in various applications like car/truck reversing indicator, computers, call bells etc. Piezo buzzer is based on the inverse principle of piezo electricity discovered in 1880 by Jacques and Pierre Curie. It is the phenomena of generating electricity when mechanical pressure is applied to certain materials and the vice versa is also true. Such materials are called piezo electric materials. Piezo electric materials are either naturally available or manmade. Piezoceramic is class of manmade material, which poses piezo electric effect and is widely used to make disc, the heart of piezo buzzer. When subjected to an alternating electric field they stretch or compress, in accordance with the frequency of the signal thereby producing sound.
Backed ourselves with sound facilities and talented workers, we have emerged as the foremost firms of best quality Mini Electronic Buzzer.
We are engaged in offering comprehensive range of Electronic Buzzers, which is also known as beeper. Our range is well known for high accuracy, durability and long lasting nature. These products are procured from our reliable vendors of the market. Further, these products are available at the most affordable rates. In addition, meeting the exact requirements of the clients, this range is available in various customized specifications at the most affordable rates.
Features:
•Exceptional strength
•Top quality
•Perfect finish
•Easy maintenance
•Optimum functionality
•Audio signalling device
•Excellent output
Metal Oxide Varistor Mov
-
-
-
- +10
Approx. Rs 2 / PieceGet Latest Price
Product BrochureProduct Details:| Minimum Order Quantity | 1000 Piece |
| Voltage Rating | 100V RMS |
| Usage/Application | Air conditioner |
| Material | Aluminium |
| Voltage | 12 - 300 V |
| Tolerance | 10% |
| Mounting Type | Through Hole |
| Color | Yellow,Blue,Red,Black |
| Phase | Single |
| Number of Pins | 2pin |
| Shape | Round |
| Operating Temp. | -55-+125 Degree |
| Features | 1.Compact design 2.Perfect finish 3.Durability 4.To protect telecommunication lines 5.High function |
| MOV | 5mm/7mm/10mm/14mm/20mm |
We deal in all types of MOVs i.e. Metal Oxide Varistor like various sizes starting from 5mm to 20mm in brands such as JVR, CNR, EPCOS, SAS etc..
The most common type of varistor is the metal-oxide varistor (MOV). This type contains a ceramic mass of zinc oxide grains, in a matrix of other metal oxides (such as small amounts of bismuth, cobalt, manganese) sandwiched between two metal plates (the electrodes). The boundary between each grain and its neighbour forms a diode junction, which allows current to flow in only one direction. The mass of randomly oriented grains is electrically equivalent to a network of back-to-back diode pairs, each pair in parallel with many other pairs.[3] When a small or moderate voltage is applied across the electrodes, only a tiny current flows, caused by reverse leakage through the diode junctions. When a large voltage is applied, the diode junction breaks down due to a combination of thermionic emission and electron tunneling, and a large current flows. The result of this behaviour is a highly nonlinear current-voltage characteristic, in which the MOV has a high resistance at low voltages and a low resistance at high voltages.
Electronics Crystal Oscillator
-
-
-
- +10
Approx. Rs 2 / PieceGet Latest Price
Product Details:| Minimum Order Quantity | 1000 Piece |
| Brand | KDS ,MEC SDE |
| Usage/Application | Industrial, Laboratory |
| Operating Temperature Range | 20 C 70 C |
| Model Number | Different Types of Model Number |
| Packaging Type | Through Hole,SMD |
| Voltage | Different Types of Voltage |
Crystals can be manufactured for oscillation over a wide range of frequencies, from a few kilohertz up to several hundred megahertz. Many applications call for a crystal oscillator frequency conveniently related to some other desired frequency, so hundreds of standard crystal frequencies are made in large quantities and stocked by electronics distributors. For example, many (non-television) applications use 3.579545 MHz crystals since they are made in large quantities for NTSC color television receivers. Using frequency dividers, frequency multipliers and phase locked loop circuits, it is practical to derive a wide range of frequencies from one reference frequency.
Leading Importers & Suppliers of Electronic Crystals.
We offer our clients a vast range ofElectronic Crystal, which are transparent in appearance and colorless with a bold mint odor. These products are sourced from trusted vendors of the industry and we offer crystals in large quantities to our clients. Our products are widely used in different industries for various purposes.
With the dedicated efforts of our diligent professionals, we have been able to offer a wide range of Oscillators Crystals to our esteemed clients. We sourced these crystals from leading manufacturers of the electronics products.
Our vendors manufactured these products implementing advanced technologies. Moreover, we are offering these within affordable price range.
We are engaged in offering our customers with a wide array of Crystal Oscillator, which is widely used in a number of applications for producing repetitive signals. The dielectric material used in these oscillators are in solid and gaseous forms. These high efficiency crystal oscillators are known for their robust and precise performance which make them ideal to be used in various programmable devices and military purposes that vibrate at an accurate frequency. These are highly appreciated and known for their outstanding electrical & mechanical stability that acquire charge when these are compressed, twisted or distorted, which make them ideal to be used in various microwave waveguide systems.
Resistor Through Hole And Smd Resistor
-
-
-
- +10
Approx. Rs 1 / PieceGet Latest Price
Product Details:| Minimum Order Quantity | 5000 Piece |
| Power Rating | 1/2 W |
| Usage/Application | Electrical Industry |
| Mounting type | Through Hole |
| Termination Style | Solder Lug |
| Shape | Cylindrical |
| Tolerance | 1%,2%,5% |
| Condition | New |
| Size | All The Size |
| CHIP | CFR/MFR/WWR/FUSABLE/NETWORK/SMD |
A electrical resistors is a two-terminal electronic component designed to oppose an electric current by producing a voltage drop between its terminals in proportion to the current, that is, in accordance with Ohm's law:
V = IR
The resistance R is equals to the voltage drop V across the resistor divided by the current I through the resistor. The various types of electrical resistors are:
- CFR
- MMR
- WWR
- Fusable
- NE
Electrical And Electronic Connectors
-
-
-
- +9
Approx. Rs 50 / PieceGet Latest Price
Product BrochureProduct Details:| Color | Different Color is Available |
| Usage/Application | Audio & Video |
| Phase | Single |
| Contact Resistance | 30m max at DC 100ma |
| Gender | Male & Female |
| Insulation Resistance | 1000m max at Dc 500v |
| Voltage | Ac 500v for 1 minute |
| Current | 1amp |
We put across a wide range of electrical connectors which are renowned for their superlative performance and quality of highest standard. Our connectors are available at cost effective prices as per the requisite requirement and specification given by the clients.
The various types of electrical connectors which are used are as following:
- RMC
- PMC
- FRC
- D-type
- PBT
- Bergsticks
- Sockets (DIP/ PLCC/ZIF)
Electronic Sensor Borads
-
-
-
- +9
Approx. Rs 250 / PieceGet Latest Price
Product Details:| Model Number | Hcsro4/hcsr501/hc06/mq2/hc05/mq3/mq5/mq7dht11/dht22 |
| Brand | Panasonic/Omron INSTRUMENTATION |
| Voltage | 5V-12V |
| Usage/Application | Instrumentation/Solar/Lighting |
| Nominal Sensing Distance | 0.1mts-10mts |
| Sensor Name | pir/ultrasonic/ldr/thermal/gas/temperature |
A sensor is a transducer whose purpose is to sense (that is, to detect) some characteristic of its environs. It detects events or changes in quantities and provides a corresponding output, generally as an electrical or optical signal; for example, a thermocouple converts temperature to an output voltage. But a mercury-in-glass thermometer is also a sensor; it converts the measured temperature into expansion and contraction of a liquid which can be read on a calibrated glass tube.
Sensors are used in everyday objects such as touch-sensitive elevator buttons (tactile sensor) and lamps which dim or brighten by touching the base, besides innumerable applications of which most people are never aware. With advances in micromachinery and easy-to-use microcontroller platforms, the uses of sensors have expanded beyond the more traditional fields of temperature, pressure or flow measurement for example into MARG sensors. Moreover, analog sensors such as potentiometers and force-sensing resistors are still widely used. Applications include manufacturing and machinery, airplanes and aerospace, cars, medicine and robotics.
A sensor's sensitivity indicates how much the sensor's output changes when the input quantity being measured changes. For instance, if the mercury in a thermometer moves 1 cm when the temperature changes by 1 °C, the sensitivity is 1 cm/°C (it is basically the slope Dy/Dx assuming a linear characteristic). Some sensors can also have an impact on what they measure; for instance, a room temperature thermometer inserted into a hot cup of liquid cools the liquid while the liquid heats the thermometer. Sensors need to be designed to have a small effect on what is measured; making the sensor smaller often improves this and may introduce other advantages.
Bourns Trimmer Potentiometer
-
-
-
- +9
Approx. Rs 50 / PieceGet Latest Price
Product Details:| Minimum Order Quantity | 1000 Piece |
| Resistance Values | 20 ohm |
| Usage/Application | Electronic Appliances |
| I am interested in | Wire wound Potentiometer |
| Resistance Range | 100 ohm to 1 m ohm |
| Voltage | Different Types of Voltage |
| Material | Pvc |
| Color | Blue |
| Part Number | Different Types of Part Number |
| Brand | Bonurs |
The measuring instrument called a potentiometer is essentially a voltage divider used for measuring electric potential (voltage); the component is an implementation of the same principle, hence its name.
Potentiometers are commonly used to control electrical devices such as volume controls on audio equipment. Potentiometers operated by a mechanism can be used as position transducers, for example, in a joystick. Potentiometers are rarely used to directly control significant power (more than a watt), since the power dissipated in the potentiometer would be comparable to the power in the controlled load.Potentiometers comprise a resistive element, a sliding contact (wiper) that moves along the element, making good electrical contact with one part of it, electrical terminals at each end of the element, a mechanism that moves the wiper from one end to the other, and a housing containing the element and wiper.
Many inexpensive potentiometers are constructed with a resistive element formed into an arc of a circle usually a little less than a full turn and a wiper sliding on this element when rotated, making electrical contact. The resistive element, with a terminal at each end, is flat or angled. The wiper is connected to a third terminal, usually between the other two. On panel potentiometers, the wiper is usually the center terminal of three. For single-turn potentiometers, this wiper typically travels just under one revolution around the contact. The only point of ingress for contamination is the narrow space between the shaft and the housing it rotates in.
Electronic Switches Buttons
-
-
-
- +3
Approx. Rs 500 / PieceGet Latest Price
Product Details:| Minimum Order Quantity | 10000 Piece |
| Current Rating | 2A to 10A |
| Material | Metal,Plastic |
| Power/Voltage | 250v |
| Operating Temp. | -20deg C to +55deg C |
| Color | Different Types of Color |
switch is an electrical component that can break an electrical circuit, interrupting the current or diverting it from one conductor to another.[1][2] The mechanism of a switch may be operated directly by a human operator to control a circuit (for example, a light switch or a keyboard button), may be operated by a moving object such as a door-operated switch, or may be operated by some sensing element for pressure, temperature or flow. A relay is a switch that is operated by electricity. Switches are made to handle a wide range of voltages and currents; very large switches may be used to isolate high-voltage circuits in electrical substations.
Electrical switches. Top, left to right: circuit breaker, mercury switch, wafer switch, DIP switch, surface mount switch, reed switch. Bottom, left to right: wall switch (U.S. style), miniature toggle switch, inline switch, push-button switch, rocker switch, microswitch.
The most familiar form of switch is a manually operated electromechanical device with one or more sets of electrical contacts, which are connected to external circuits. Each set of contacts can be in one of two states: either "closed" meaning the contacts are touching and electricity can flow between them, or "open", meaning the contacts are separated and the switch is nonconducting. The mechanism actuating the transition between these two states (open or closed) can be either a "toggle" (flip switch for continuous "on" or "off") or "momentary" (push-for "on" or push-for "off") type.
Pnp Power Transistor
-
-
-
- +9
Approx. Rs 1 / PieceGet Latest Price
Product Details:| Minimum Order Quantity | 2000 Piece |
| Current | 10 A |
| Mounting Type | DIP |
| No. Of Pins | 3 Pin |
| Brand | CDIL |
| Number Of Pins | 3 Pin |
| Color | Black |
| Is It Non-Linear Resistors | Linear Resistors |
| Variable Resistors | Yes |
| Fixed Resistors | Yes |
| Condition | New |
We supply optimum quality high voltage transistors and diodes which are sourced from reliable and trusted partners across the globe. These are mainly used in amplifiers or switches for electrical signals. Some of the salient features of our transistors and diodes are as follows:
- Small size & minimal weight
- Highly automated
- Requires low operating voltage
- Reliable
- Low power dissipation
The extensive range of high voltage transistors includes:
- 2N
- MJE
- TIP
- BDX
- BU/ BD / BC –series
The varied range of diodes includes:
- ZENER/ TVS
- Bridge rect/ FRD/ SCHOTTKY
Electronic Relay Parts
-
-
-
- +9
Approx. Rs 50 / PieceGet Latest Price
Product Details:| Minimum Order Quantity | 100 Piece |
| Parts | Relay Board |
| Brand | 2 Pole |
| Color | Black/Yellow/Blue |
| Contact Form | SPDT |
| Shape | Square/Box/T-type |
| Phase | Single Phase |
| Voltage | 5v,6v,12v,24v |
| Voltage Type | AC |
We source and supply optimum quality switch relays, which is an electrical switch that opens and closes under the control of another electrical circuit. Our range is based on latest technology to offer easy and effective operation. Some of our switch relays comprises of the following:
- Sugar cube
- Telcom
- Power
Electronic Piezo Buzzer
-
-
-
- +9
Approx. Rs 10 / PieceGet Latest Price
Product Details:| Minimum Order Quantity | 1000 Piece |
| Voltage | 12.0 V |
| Brand | Different Type of Brand |
| Frequency | 2.8 KHz |
| Color | Black |
| Buzzer Size | 42MM |
| Decibel Speakers | 85db 10cm |
| Material | FR4 + ABS |
Backed ourselves with sound facilities and talented workers, we have emerged as the foremost firms of best quality Mini Electronic Buzzer.
We are engaged in offering comprehensive range of Electronic Buzzers, which is also known as beeper. Our range is well known for high accuracy, durability and long lasting nature. These products are procured from our reliable vendors of the market. Further, these products are available at the most affordable rates. In addition, meeting the exact requirements of the clients, this range is available in various customized specifications at the most affordable rates.
Features:
•Exceptional strength
•Top quality
•Perfect finish
•Easy maintenance
•Optimum functionality
•Audio signalling device
•Excellent output
Light Emitting Diode Round,Flat
-
-
-
- +9
Approx. Rs 20 / PieceGet Latest Price
Product Details:| Minimum Order Quantity | 1000 Piece |
| LED Color | Red/green/yellow/Blue/white/Warm-White/Pink/Orange |
| Shape | Round,Flat |
| Color | Red,Blue,Green,Yellow,White,elc |
| Wattage | 6W |
| Number Fo Pin | 2pin,3pin,4pin |
| LED Type | Through Hole LED |
| Condition | New |
A light-emitting diode (LED) is a semiconductor light source. LEDs are used as indicator lamps in many devices and are increasingly used for other lighting. Appearing as practical electronic components in 1962,[7] early LEDs emitted low-intensity red light, but modern versions are available across the visible, ultraviolet, and infrared wavelengths, with very high brightness.
When a light-emitting diode is switched on, electrons are able to recombine with holes within the device, releasing energy in the form of photons. This effect is called electroluminescence and the color of the light is determined by the energy band gap of the semiconductor. A LED is often small in area (less than 1 mm2), and integrated optical components may be used to shape its radiation pattern. LEDs present many advantages over incandescent light sources including lower energy consumption, longer lifetime, improved physical robustness, smaller size, and faster switching. However, LEDs powerful enough for room lighting are relatively expensive and require more precise current and heat management than compact fluorescent lamp sources of comparable output.
SPDT Electronic Instruments Switches
-
-
-
- +9
Approx. Rs 100 / PieceGet Latest Price
Product Details:| Minimum Order Quantity | 1000 Piece |
| Pressure Switch Type | Electronic Pressure Switch |
| Switch Configuration | SPDT |
| Current Rating (In Amps) | 2A/3A/4A/6A/16A |
| Application | Electronic Instruments |
| Material | Plastic |
| Power/Voltage | 230V |
| Color | Red,Black,Orange |
| Switch Type | Modular, Bell Push Switches, Regular, Three Pin |
We have the exhaustive range of the appliance switches, fuse and fuse holders which are of very efficient performance and of the highest quality standard. These are available in various models and sizes as per the requisite specification given by the client’s. Our comprehensive range of appliance switches includes the following:
- Toggle
- Rocker
- Micro
- Push button
- Dip
- Tact
- Reed fuses
A fuse (short for fusible link), is a type of over current protection device. Its essential component is a metal wire or strip that melts when too much current flows, which breaks the circuit in which it is connected, thus protecting the circuit's other components from damage due to excessive current.
The different fuse holders are:
- Glass
- Thermal
- Ceramic
- Resettable
Power Inductor Smd
-
-
-
- +9
Approx. Rs 12 / PieceGet Latest Price
Product Details:| Minimum Order Quantity | 2000 Piece |
| Inductor Type | DIP, SMD/DIP |
| Material | Copper |
| Inductance Range | 1mH-100mH & 1uH-100uH |
| Color | Black |
| Power | 220V |
| Usage/Application | Electric Devices |
| Product Type | Power Inductor Smd |
Ø An inductor is a passive component that is used in most power electronic circuits to store energy in the form of magnetic energy when electricity is applied to it. One of the key properties of an inductor is that it impedes or opposes any change in the amount of current flowing through it.
Ø An inductor, also called a coil, choke, or reactor, is a passive two-terminal electrical component that stores energy in a magnetic field when electric current flows through it.[1] An inductor typically consists of an insulated wire wound into a coil.
Ø An inductor is characterized by its inductance, which is the ratio of the voltage to the rate of change of current. In the International System of Units (SI), the unit of inductance is the henry (H) named for 19th century American scientist Joseph Henry. In the measurement of magnetic circuits, it is equivalent to weber/ampere. Inductors have values that typically range from 1 µH (10−6 H) to 20 H. Many inductors have a magnetic core made of iron or ferrite inside the coil, which serves to increase the magnetic field and thus the inductance. Along with capacitors and resistors, inductors are one of the three passive linear circuit elements that make up electronic circuits. Inductors are widely used in alternating current (AC) electronic equipment, particularly in radio equipment. They are used to block AC while allowing DC to pass; inductors designed for this purpose are called chokes. They are also used in electronic filters to separate signals of different frequencies, and in combination with capacitors to make tuned circuits, used to tune radio and TV receivers.
Ø Inductors have a wide range of applications in electronics and electrical engineering. They are commonly used in power supplies to filter out high-frequency noise, in transformers to change voltage levels, and in radio frequency (RF) circuits for tuning and impedance matching. Inductors also play a crucial role in electric motors, chokes, and various sensor applications
Ksd 301 Heating Thermostat
-
-
-
- +7
Approx. Rs 30 / PieceGet Latest Price
Product Details:| Minimum Order Quantity | 500 Piece |
| Usage/Application | Heaters,Temperature Control |
| Body Material | Plastic |
| Temperature Range | 40 C - 260 C |
| Voltage | 220V |
| Model No | KSD301 |
| Current Rating | 10amp |
| Application | Temperature Controlling Purpose |
| Fuse Type | Thermal Cut off Fuse |
A thermostat is a component of a control system which senses the temperature of a system so that the system's temperature is maintained near a desired setpoint. The thermostat does this by switching heating or cooling devices on or off, or regulating the flow of a heat transfer fluid as needed, to maintain the correct temperature. The name is derived from the Greek words thermos "hot" and statos "a standing".
A thermostat may be a control unit for a heating or cooling system or a component part of a heater or air conditioner. Thermostats can be constructed in many ways and may use a variety of sensors to measure the temperature. The output of the sensor then controls the heating or cooling apparatus. A Thermostat may switch on and off at temperatures either side of the setpoint the extent of the difference is known as hysteresis and prevents too frequent switching of the controlled equipment.
Power Semiconductor Diodes
-
-
-
- +9
Approx. Rs 15 / PieceGet Latest Price
Product Details:| Minimum Order Quantity | 5000 Piece |
| Usage/Application | Industrial |
| Material | Superior Quality |
| Current | 1A-100A |
| Brand | Fuji |
| Voltage | 100V-1600V |
| Model Number | IN4007,IN4148,elc,etc |
| Color | Black,Orange |
Diode is a two-terminal electronic component with asymmetric conductance; it has low (ideally zero) resistance to current in one direction, and high (ideally infinite) resistance in the other. A semiconductor diode, the most common type today, is a crystalline piece of semiconductor material with a p-n junction connected to two electrical terminals.[5] A vacuum tube diode has two electrodes, a plate (anode) and a heated cathode. Semiconductor diodes were the first semiconductor electronic devices. The discovery of crystals' rectifying abilities was made by German physicist Ferdinand Braun in 1874. The first semiconductor diodes, called cat's whisker diodes, developed around 1906, were made of mineral crystals such as galena. Today, most diodes are made of silicon, but other semiconductors such as selenium or germanium are sometimes used.
Explore More Products
Sheth Electronics
Bengaluru - 560020, Karnataka, India
© Sheth Electronics. All Rights Reserved (Terms of Use)
Developed and Managed by IndiaMART InterMESH Limited